PE Digital Stamps Logo

Generate digital Arkansas Engineer (PE) stamps instantly

  • STATE BOARD APPROVED
  • HIGH-QUALITY FILES IN VARIOUS FORMATS
  • INSTANT ACCESS
  • FREE-OF-CHARGE REVISIONS
Loading seal preview
Text Size
Text Size

Your board-compliant seal will be ready for download after purchase

Arkansas PE Stamp Requirements

Board approved

Your Arkansas Professional Engineer seal from pedigitalstamps.com meets every requirement on this page — the required wording, the layout and the diameter set out in 17 CAR § 285-602 (Seals). Fill in your details and download it in seconds.

The Arkansas rules in full, with citations

The Board's rules were recodified into the Code of Arkansas Rules of 2024, which is what renumbered the seal rule out of the Board's pre-2024 article numbering into 17 CAR § 285-602. The substance is unchanged from the text effective June 1, 2022. Seals previously acquired in compliance with then current rules need not be changed.

Professional Engineer seal

Board:
State Board of Licensure for Professional Engineers and Professional Surveyors
Rule:
17 CAR § 285-602 (Seals)
Diameter:
From one and one-quarter inch (1 ¼ in.) to two inches (2 in.) in diameter, with a milled edge.
Legend:
“Licensed Professional Engineer”
  • The seal bears the licensee's name, license number, and the legend "licensed professional engineer". (17 CAR § 285-602(a)(1))
  • The engineer seal shall use the design printed in the rule: STATE OF ARKANSAS across the top with the state outline, LICENSED PROFESSIONAL ENGINEER stacked in the center, the number below it, and the licensee's name across the bottom. (17 CAR § 285-602(d)(1)(A))
  • A facsimile rubber stamp is authorized in lieu of a seal, and may have either a milled edge or two concentric circles corresponding with the respective edges of the milling. (17 CAR § 285-602(d)(2)(B)-(C))
  • The name and number inscribed in the seal must correspond to the name and certificate number shown on the certificate of licensure. (17 CAR § 285-602(d)(2)(D))
  • Each page of each final engineering document, the cover sheet of specifications and the signature page of written reports must be dated, signed, and stamped when issued. (17 CAR § 285-602(a)(2))
  • Record or as-built drawings shall not be sealed unless specifically required by contract, and then must carry a caveat identifying the source and basis of the information and stating that the drawing cannot be guaranteed accurate. (17 CAR § 285-602(a)(4))
  • Documents may be sealed electronically. A digitally signed document may be transmitted electronically if the signature is unique to and under the sole control of the person who applied it, capable of verification, and invalidated if any data on the document is altered. (17 CAR § 285-602(d)(5)(A))
  • A document sealed but not signed that is transmitted electronically must carry: "This document was originally issued and sealed by (name of licensee), (license number) on (date). This copy is not a signed and sealed document." (17 CAR § 285-602(d)(5)(B)(ii))

Full Arkansas PE seal requirements, with every citation →

File formats

All formats included

format preview

HIGH-QUALITY RASTER FORMAT

format preview

VECTOR FORMAT, INFINITELY SCALABLE

format preview

UNIVERSAL DOCUMENT FORMAT

format preview

AUTOCAD COMPATIBLE FORMAT

format preview

PROFESSIONAL PRINT FORMAT

How it works

Create your Arkansas digital PE stamp

1

Select your state & profession

2

Add your name & license number

3

Adjust the text size using the controls

4

Select your discipline

5

Add your signature & customize (optional)

6

Download instantly to your computer

Digital PE stamp with callouts showing where the name, license number and other details go

Software compatibility

Compatible with PDF and CAD software

Bluebeam
Adobe Acrobat
Arkansas PE stamp applied to a PDF drawing in Bluebeam Revu
AutoCAD
Autodesk Revit
Arkansas PE stamp DXF opened in AutoCAD

Who we are

About

Our digital Arkansas PE stamp generator creates instant state-approved electronic pe stamps. Our platform provides full customization of your digital seal, including an option to add your signature. Professional Engineer (PE) stamps, Architect stamps, and Land Surveyor stamps are available for immediate download after customization. There is no waiting. Every electronic professional seal we generate is 100% compliant with state board requirements, ensuring your digital stamp meets all necessary standards.

State boards

State board-approved, including

  • California Board for Professional Engineers, Land Surveyors, and Geologists logo
  • Texas Board of Professional Engineers and Land Surveyors logo
  • Florida Board of Professional Engineers logo
  • New York State Education Department, Office of the Professions logo
  • Pennsylvania State Registration Board for Professional Engineers, Land Surveyors and Geologists logo
  • Ohio Board of Registration for Professional Engineers and Surveyors logo
  • Georgia State Board of Registration for Professional Engineers and Land Surveyors logo
  • North Carolina Board of Examiners for Engineers and Surveyors logo
  • Washington State Board of Registration for Professional Engineers and Land Surveyors logo
  • Minnesota Board of Architecture, Engineering, Land Surveying, Landscape Architecture, Geoscience and Interior Design logo
  • Louisiana Professional Engineering and Land Surveying Board logo
  • Oklahoma State Board of Licensure for Professional Engineers and Land Surveyors logo

FAQ

Arkansas Engineer Seal FAQs

Frequently asked questions about Arkansas digital engineer stamps and seals.

How do I obtain a digital Arkansas professional engineer (PE) seal or stamp?

Once you are licensed in Arkansas, you can generate your seal here and download it immediately. Fill in the form and position your signature if you want one. The layout follows 17 CAR § 285-602 (Seals), which is the provision the State Board of Licensure for Professional Engineers and Professional Surveyors will measure the seal against.

What are the requirements for the Arkansas PE stamp or seal?

Arkansas’ PE seal rule is 17 CAR § 285-602 (Seals), administered by the State Board of Licensure for Professional Engineers and Professional Surveyors. The seal must carry “Licensed Professional Engineer”, and from one and one-quarter inch (1 ¼ in.) to two inches (2 in.) in diameter, with a milled edge.

A further 8 requirements, each tied to the subsection that imposes it, are itemised in the Arkansas requirements section on this page.

What size does an Arkansas PE seal have to be?

From one and one-quarter inch (1 ¼ in.) to two inches (2 in.) in diameter, with a milled edge. This is set by 17 CAR § 285-602(d)(2)(A).

How small can an Arkansas engineer's seal be, and does it need a milled edge?

The floor is 1 ¼ inches, lower than most states, and the rule requires a milled edge conforming to the printed design. A rubber stamp may substitute two concentric circles matching the edges of the milling. (17 CAR § 285-602(d)(2)(A)-(C))

Does an Arkansas seal have to say "State of Arkansas"?

"State of Arkansas" is required by the mandatory illustrated design, not by the element list in the rule's opening paragraph, which names only name, number and legend. (17 CAR § 285-602(d)(1)(A))

Can I put a shortened form of my name on an Arkansas seal?

The name and number on the seal must correspond to the certificate of licensure. An abbreviated or preferred form of the name is not authorized. (17 CAR § 285-602(d)(2)(D))

Should as-built drawings be sealed in Arkansas?

Record and as-built drawings are not to be sealed at all unless the contract specifically requires it, and then only with the prescribed caveat. (17 CAR § 285-602(a)(4))